-
Mark Logo on Plastic, Metal, and Every Material with Laser Markers
May 07 , 2021
A Certification Mark is a permanent mark placed, labeled, or engraved onto a part that indicates the product meets or exceeds the required standards to sell a good within an geographic area. These marks certify the product conforms with safety, health and environmental protection standards. The CE mark is the standard for the EU/European Economic Area. The United Kingdom previously us...
view more
-
What is a Green Laser?
May 07 , 2021
What is a Green Laser? Creating permanent traceability marks is critical for many manufacturers. Sometimes, very delicate materials require the use of non-traditional methods and equipment to achieve this because the item is sensitive or the absorption ratio is so low that it is very difficult to get a readable amount of contrast in the permanent mark (2D Matrix Code or human-readable text)....
view more
-
What can be marked with a laser and how does one do that?
May 07 , 2021
What can be marked with a laser and how does one do that? It would be great if someone could create a “recipe book” that would give specific settings for laser marking any type of material on any type or make of laser marking system. Good luck finding that. Different laser marking systems from different manufacturers can yield different results on the same material for several reasons....
view more
-
15W high-power UV laser is needed to solve the problem of PCB burr
May 07 , 2021
15W high-power UV laser is needed to solve the problem of PCB burr In general, the surface of metal parts and the surface of small microscopic metal particles appear, these are called burrs. The more burrs, the lower the yield of PCB circuit boards. Causes of burrs: The cutting edge becomes dull and the gap is too large; the saw blade is dull or improperly installed; the punch is wor...
view more
-
High-power UV laser cutting technology to avoid PCB circuit board burrs
May 07 , 2021
High-power UV laser cutting technology to avoid PCB circuit board burrs In general, the surface of metal parts and the surface of small microscopic metal particles appear, these are called burrs. The more burrs, the lower the yield of PCB circuit boards. Causes of burrs: The cutting edge becomes dull and the gap is too large; the saw blade is dull or improperly installed; the punch is worn ...
view more
-
10W-15W high-power ultraviolet laser is specially designed to solve PCB circuit board burrs
May 07 , 2021
10W-15W high-power ultraviolet laser is specially designed to solve PCB circuit board burrs In general, the surface of metal parts and the surface of small microscopic metal particles appear, these are called burrs. The more burrs, the lower the yield of PCB circuit boards. Causes of burrs: The cutting edge becomes dull and the gap is too large; the saw blade is dull or improperly in...
view more
-
What is the difference between laser marking and laser engraving?
May 06 , 2021
Laser Marking vs. Engraving December 6, 2017Jim EarmanLaser Engraving, laser marking0 Comments Over the years we’ve gotten a lot of questions about the various marking techniques that can be accomplished with a fiber laser marking system. The terms “Laser Marking” and “Laser Engraving” are frequently used interchangeably but there is a difference. Generally speaking, ...
view more
-
Hole Drilling by Laser
May 06 , 2021
Hole Drilling by Laser This section introduces laser processing-based drilling through examples. Basic principles of drilling using laser markers Hole drilling example — Drilling holes in rice bags Recommended models for hole drilling, organised by material Basic principles of drilling using laser markers Laser-based drilling uses laser light to irradiate a single point of a target in...
view more
-
Basic principles of cutting using laser markers
May 06 , 2021
Laser Cutting This section introduces laser processing-based laser cutting through examples. Basic principles of cutting using laser markers Laser cutting example — Laser cutting of electric wire coating Basic principles of etching using laser markers Etching example — Creating perforations on film Recommended models for laser cutting, organised by material Basic principles of c...
view more
-
Basic principles of paint peeling using laser markers
May 06 , 2021
Laser Etching This section introduces laser processing-based peeling through examples. Basic principles of paint peeling using laser markers Paint peeling example — On-board instrument panel switch coating removal Basic principles of surface peeling using laser markers Surface peeling example 1 — ITO film removal Surface peeling example 2 — Peeling off gold plating from co...
view more
