10W-15W uv laser

Expert III 355 Ultra-stable Nanosecond UV Laser 10W12W15W

Expert III 355 series UV DPSS laser, developed and produced by RFH, covers 10w-15w in laser power with short pulse width (<20ns@40K) ,superior beam quality (M²<1.2) and perfect laser spot quality (beam circularity >90%). It is widely used in PE/PCB/FPC cutting, glass & sapphire cutting, drilling, scribing & cutting used in high precision micromaching areas.

  • Laser Wavelength:

    354.7nm
  • Average Output Power :

    10W/12W/15W @40kHz
  • Pulse Width:

    <20ns @40kHz
  • Pulse Repetition Rate :

    10-200kHz
  • Spatial Mode:

    TEM00
  • Beam Quality (㎡) :

    <1.2
  • Beam Diameter:

    0.8±0.1mm Measured at window
  • Beam Full Divergence Angle :

    <2mrad
  • Beam Circularity:

    >90%
  • Pulse-To-Pulse Stability:

    <3% RMS/@30kHz
  • Average Power Stability :

    <5% RMS/8hr
  • Beam-Pointing Drift:

    <25μrad/℃
  • Polarization Ratio:

    >100:1
  • Polarization Orientation:

    Horizontal
  • Operating Temp. & RH:

    10℃ to 35℃ | <80%
  • Storage Temp. & RH:

    10℃ to 35℃ | <90 %
  • Electricity Requirement :

    100-240VAC |50/60Hz | Single phase
  • Power Consumption:

    <800W
  • Warranty :

    18months
  • Product Detail
  • Video

uv laser

Expert III 355 series UV DPSS laser, developed and produced by RFH, covers 10w-15w in laser power with short pulse width (<20ns@40K) ,superior beam quality (M²<1.2) and perfect laser spot quality (beam circularity >90%). It is widely used in PE/PCB/FPC cutting, glass & sapphire cutting, drilling, scribing & cutting used in high precision micromaching areas.

UV LASER

 

Expert III 355 series uv laser characteristics:   

1. 355 nm output wavelength, 10 to 200 Hz repetition rate; laser power ranging from 10w-15w; Continuous tuning of repetition rate while maintaining constant pulse energy, superior beam pointing and energy stability make the Expert III 355 the first choice for micromachining, marking and thin film removal applications 

 

2. Exceptional beam quality (M²<1.2) ,absolutely assured in all repetition rates; relatively short pulse width <20ns@40K with little heat transfer to surrounding material; perfect beam spot quality(Beam Circularity>90%) 

Close to Gaussian smooth beam profile with low value M² < 1.2 and good focusability are beneficial for applications such as  

 

3. Unique Q-switching technology, adapts a variety of control requirements of laser applications;Online refreshment for harmonic coupling technology;Excellent long term power stability Rugged sealed cavity, Extremely compact size, Simple and robust 

 

4. Digital control technology for the driver,  RS232 control interface ensures easy control and integration with laser marking equipment 

 

5. This laser adopts one - style design with compact and reasonable structure, easy installation. 

Easy to transport and saves space due to compact and light design 

 

Water cooling,cost-effective and reliable end-pumping technology and amplifier-free DPSS design guarantee easy operation and alignment simple installation and low maintenance costs

 

6. Industrial production process control technology,provides quality stable products.

Nanosecond UV Laser

Nanosecond UV Laser

 

 RFH - The leading industrial solid-state laser manufacturer

 

For over 13 years with excellent long term stability and exceptional good beam quality

 

Production in dust-free plant & rigorous quality control system

From purchasing, pre-production quality check, assembling, finished product testing, warehouse-in inspection, pre-delivery testing to after-sales service, each step is under control to make sure product quality and consistency in both machine parameters and actual running parameters. This is what makes RFH laser lasts longer than its peers. 

RFH LASER

Top professional team, independent R&D in laser oriented power supply control system

 

There is a one-to-one correspondence between power supply and laser. The stability of power supply control system determines if the laser can maximize its performance during operation. RFH Laser has independent R&D in power supply technique which enables timely update and improvement of power supply control system module based on the laser’s need. 12-year experience in R&D and a top professional team make RFH laser a reliable and stable laser system.

LASER POWER SUPPLY

Core components of oversea brands with guaranteed quality

Pumping, Q-switching and other core components adopt oversea brands. Work with top brand component suppliers of home and abroad. Each component is guaranteed with its quality from the beginning of materials purchasing. This is why users can trust RFH laser.  

Nanosecond UV Laser

 

UV laser+power supply+cooling system sold in a group

Being client-oriented, RFH offers proposal of selling the whole laser system in a group so that the laser system can maximize its performance while maintaining its stability. 

Nanosecond UV Laser

 

Full-digital display, supporting communication with computer, capable of laser’s remote control

Each laser developed and produced by RFH can always remain high quality in industrial and extreme conditions of scientific research. With stable beam quality, high efficiency, best cost performance and high reliability, RFH has earned good reputation in different industries at home and abroad. After 12-year development, RFH has become a reputed brand in nanosecond laser industry. 

UV LASER

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Related products
RFH 532nm green laser marking glass with ±0.02mm High precision
RFH 532nm green laser marking glass with ±0.02mm High precision
RFH 532nm green laser marking glass with ±0.02mm High precision 532nm green laser is a great accomplishment of RFH which has 13 years of R&D experience. It has perfect beam spot quality(Beam Circularity>90%) , relatively short pulse width <35ns@30K with little heat transfer to surrounding material and exceptional beam quality (M²<1.3) absolutely assured in all repetition rates. These features of 532nm green laser guarantee fast marking speed and delicate marking performance.  In addition, RFH 532nm green laser has independent R&D in power supply technique,which enables timely update and improvement of power supply control system module based on the laser’s need. The unique Q-switching technology makes it applicable to a variety of control requirements of laser applications. Online refreshment for harmonic coupling technology ensures its long life time. Therefore, RFH 532nm green laser is very ideal to be integrated into UV laser glass marking machine.
RFH 532nm green laser marking glass with ±0.02mm High precision
355nm UV laser cutting PCB with no burrs and no glue overflow
355nm UV laser cutting PCB with no burrs and no glue overflow
355nm UV laser cutting PCB with no burrs and no glue overflow FPC requires a laser cutting machine to depanel and then install on different electronics. As all know, UV laser plays an important role in FPC laser cutting machine. It is a cold light source with small heat-affecting zone of 10μm, making it applicable to perform cutting, depaneling, drilling on FPC and rigid-flex PCB with perfect cutting performance.   With fast speed, high precision of ±0.02mm and high stability, RFH 355 series UV laser has become a well-known brand among FPC and PCB cutting, drilling, depanling and engraving clients.   
355nm UV laser cutting PCB with no burrs and no glue overflow
K-6 Integrated UV Laser 4W-6W
K-6 Integrated UV Laser 4W-6W-8W
K-6 series UV DPSS laser, developed and produced by RFH, covers 4W/6W/8W in laser power with short pulse width (<20ns@30K) ,superior beam quality (M²<1.2) and perfect laser spot quality (beam circularity >90%). K-6 series laser is ideal for high-end ultra-precise processing as well as marking in mobile phone shell , package of cosmetics, food, medicine and other high polymer materials, PCB, LCD, glassware surface, metal’s cladding material, plastic keypad, electronic component, gift, communication device, construction material and other areas.
Download datasheet
K-6 Integrated UV Laser 4W-6W
S9-Y series Integrated 3W-10W UV laser
S9-Y series Integrated 3W-10W UV laser
S9-Y series solid state pulsed UV laser is ultra compact. The whole part of power supply is integrated into the laser head. This makes the size of the laser more smaller, and the integration into a system more easier and convenient. S9-Y series is of short pulse width(<12ns@30k),superior beam quality(M²<1.2) and perfect laser sport quality(beam circularity>90%).
Download datasheet
S9-Y series Integrated 3W-10W UV laser
UV laser
UV laser can cut screen protector tempered glass film with smooth and even cutting edges
RFH 355nm UV laser can cut screen protector tempered glass film with smooth and even cutting edges   With touch screen being increasingly used, the demand of mobile phone tempered glass film is also increasing. However, the sizes of different mobile phone brands are different, so the tempered glass film needs to be cut and drilled to required size. In the past, people used traditional CNC cutting technique on tempered glass film, but this method can easily lead to micro cracks or broken edges. So how to prevent tempered glass film from damaging during the cutting process? Well, RFH UV laser can help. The tempered glass film using RFH 355 series UV laser to drill and cut on won’t damage because of heat or crack because of instability. Instead, its cutting edges are quite smooth and the drilled holes are very round, making it more suitable to be used in smart phones.
UV laser
532 green laser is used to laser mark on ceramic knife
532 green laser is used to laser mark on ceramic knife
532 green laser is used to laser mark on ceramic knife Using RFH 532nm green laser to laser mark on ceramic knife enables the pattern on it to be very clear and doesn’t affect its normal cutting performance. This maximizes the brand quality and the delicacy of the ceramic knife.   Today, RFH is going to share the case of a ceramic knife supplier whose peer recommends RFH 10W 532nm green laser to him.    As we all know, marking on a ceramic knife adopts a laser marking technique. The whole marking process on the ceramic knife is so simple and generally takes a few seconds to finish. But this seemingly “simple” process needs to be supported by a well-established technique.And that is a laser system with exceptional laser beam quality and its accessories. An excellent laser is the basis of 99% yield of laser marking product and the solid-state green laser produced by RFH with 13-year experience is the perfect example.   
532 green laser is used to laser mark on ceramic knife
UV laser
UV laser featuring cold processing for marking plastic button on keyboard
 UV laser featuring cold processing for marking plastic button on keyboard More and more manufacturers choose UV laser marking machine to create pattern and characters on the plastic button switch. The focal spot of UV laser is pretty small with little heat transfer to surrounding material, so UV laser is also called “cold light source”. Because of this feature, heat effect won’t occur. Thus, distorting or burning of materials is no longer an issue.    Professional UV laser manufacturer - Shenzhen RFH Laser Technology Co.,Ltd    With 13 years of experience, the S9 series nanosecond UV laser developed and produced by RFH can engrave clear characters on the keyboard and the mouse. These kinds of characters can not only help people identify different buttons in the dark but also last long, for there are slightly protruding part on the buttons. This improves the durability and practicability of the keyboard and the mouse.   
UV laser
Expert III 532 Green laser 35W
Expert III 532 Green laser 35W
Expert III 532 series green DPSS laser, developed and produced by RFH, covers 35w in laser power with short pulse width (<25ns@50K) ,superior beam quality (M²<1.2) and perfect laser spot quality (beam circularity >90%).It is perfect for glass marking,thin film etching and surface treatment for most of the metals and non-metal materials, such as removing the oxide layer from the metal surface
Download datasheet
Expert III 532 Green laser 35W
Get the latest offers Subscribe for our newsletter

Please read on, stay posted, subscribe, and we welcome you to tell us what you think.

leave a message
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

About

contact