10W-15W uv laser

S9 series 532 Green laser 5W/10W

S9 series green DPSS laser, developed and produced by RFH, covers 5w/10w in laser power with short pulse width (<14ns@30K) ,superior beam quality (M²<1.2) and perfect laser spot quality (beam circularity >90%). It is particularly suitable for drilling and scribing in ceramics, marking, cutting and drilling in glass & wafer and surface treatment in most of the metal and non-metal materials. 

  • Laser Wavelength:

    532nm
  • Average Output Power :

    5W/10W @30kHz
  • Pulse Width:

    <14ns @30kHz
  • Pulse Repetition Rate :

    10-200kHz
  • Spatial Mode:

    TEM00
  • Beam Quality (㎡) :

    <1.2
  • Beam Diameter:

    0.8±0.2mm Measured at window
  • Beam Full Divergence Angle :

    <1.2mrad
  • Beam Circularity:

    >90%
  • Pulse-To-Pulse Stability:

    <2% RMS/@30kHz
  • Average Power Stability :

    <5% RMS/8hr
  • Beam-Pointing Drift:

    <30μrad/℃
  • Polarization Ratio:

    >100:1
  • Polarization Orientation:

    Horizontal
  • Operating Temp. & RH:

    10℃ to 30℃ | <80%
  • Storage Temp. & RH:

    -20℃ to 65℃ | <90 %
  • Electricity Requirement :

    100-240VAC |50/60Hz | Single phase
  • Power Consumption:

    <500W
  • Warranty :

    18months
  • Product Detail
  • Video

uv laser

S9 series green DPSS laser, developed and produced by RFH, covers 5w/10w in laser power with short pulse width (<14ns@30K) ,superior beam quality (M²<1.2) and perfect laser spot quality (beam circularity >90%). It is particularly suitable for drilling and scribing in ceramics, marking, cutting and drilling in glass & wafer and surface treatment in most of the metal and non-metal materials. 

GREEN LASER

 

S9 series green laser characteristics:   

1. 532nm output wavelength, 10 to 200 Hz repetition rate; laser power is 5w/10W; Continuous tuning of repetition rate while maintaining constant pulse energy, superior beam pointing and energy stability make the Excellent III 532 the first choice for micromachining, marking and thin film removal applications 

 

2. Exceptional beam quality (M²<1.2) ,absolutely assured in all repetition rates; relatively short pulse width <14ns@30K with little heat transfer to surrounding material; perfect beam spot quality(Beam Circularity>90%) 

Close to Gaussian smooth beam profile with low value M² < 1.2 and good focusability are beneficial for applications such as  

 

3. Unique Q-switching technology, adapts a variety of control requirements of laser applications;Online refreshment for harmonic coupling technology;Excellent long term power stability Rugged sealed cavity, Extremely compact size, Simple and robust 

 

4. Digital control technology for the driver,  RS232 control interface ensures easy control and integration with laser marking equipment 

 

5. This laser adopts one - style design with compact and reasonable structure, easy installation. 

Easy to transport and saves space due to compact and light design 

 

Water cooling,cost-effective and reliable end-pumping technology and amplifier-free DPSS design guarantee easy operation and alignment simple installation and low maintenance costs

 

6. Industrial production process control technology,provides quality stable products.

 

 

 RFH - The leading industrial solid-state laser manufacturer

 

For over 13 years with excellent long term stability and exceptional good beam quality

 

Production in dust-free plant & rigorous quality control system

From purchasing, pre-production quality check, assembling, finished product testing, warehouse-in inspection, pre-delivery testing to after-sales service, each step is under control to make sure product quality and consistency in both machine parameters and actual running parameters. This is what makes RFH laser lasts longer than its peers. 

RFH LASER

Top professional team, independent R&D in laser oriented power supply control system

 

There is a one-to-one correspondence between power supply and laser. The stability of power supply control system determines if the laser can maximize its performance during operation. RFH Laser has independent R&D in power supply technique which enables timely update and improvement of power supply control system module based on the laser’s need. 12-year experience in R&D and a top professional team make RFH laser a reliable and stable laser system.

green laser

Core components of oversea brands with guaranteed quality

Pumping, Q-switching and other core components adopt oversea brands. Work with top brand component suppliers of home and abroad. Each component is guaranteed with its quality from the beginning of materials purchasing. This is why users can trust RFH laser.  

 

Green laser+power supply+cooling system sold in a group

Being client-oriented, RFH offers proposal of selling the whole laser system in a group so that the laser system can maximize its performance while maintaining its stability. 

 

 

Full-digital display, supporting communication with computer, capable of laser’s remote control

Each laser developed and produced by RFH can always remain high quality in industrial and extreme conditions of scientific research. With stable beam quality, high efficiency, best cost performance and high reliability, RFH has earned good reputation in different industries at home and abroad. After 12-year development, RFH has become a reputed brand in nanosecond laser industry. 

uv laser | green laser | Ultraviolet lasers | uv dpss laser | nanosecond laser | UV laser source | Solid State Lasers

UV LASER

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Related products
532 Green laser 18W-35W
Excellent III 532 Green laser 18W-35W
Excellent III 532 series green DPSS laser, developed and produced by RFH, covers 18w-35w in laser power with short pulse width (<7-8ns@40K) ,superior beam quality (M²<1.2) and perfect laser spot quality (beam circularity >90%). It is particularly suitable for drilling and scribing in ceramics, marking, cutting and drilling in glass & wafer and surface treatment in most of the metal and non-metal materials. 
532 Green laser 18W-35W
RFH 355nm UV laser marking on N95 face mask for QR code
RFH 355nm UV laser marking on N95 face mask for QR code
RFH 355nm UV laser marking on N95 face mask for QR code As the main material of the N95 face mask, meltblown cloth has a thin surface and cannot be processed in a hot environment casually. Other laser light sources will produce high temperatures during processing. Only short-wavelength (355nm) ultraviolet lasers have little thermal impact and will not produce high temperatures during marking. What’s more, it will not cause damage to the N95 face mask.   
RFH 355nm UV laser marking on N95 face mask for QR code
marking barcode
RFH 355nm UV laser marking barcode, label on the fly on IC card
RFH 355nm UV laser marking barcode, label on the fly on IC card   IC card is a microelectronic chip embedded in the card base, which can communicate with the card reader in a non-contact or contact way after being made into a card form. Used in many places. Today, more extensive technology allows IC cards to be marked with labels and barcodes, and the scope of use is wider.
marking barcode
RFH UV laser is applicable to cut, drill an depanel on FPC
RFH UV laser is applicable to cut, drill an depanel on FPC
RFH UV laser is applicable to cut, drill an depanel on FPC FPC requires a laser cutting machine to depanel and then install on different electronics. As all know, UV laser plays an important role in FPC laser cutting machine. It is a cold light source with small heat-affecting zone of 10μm, making it applicable to perform cutting, depaneling, drilling on FPC and rigid-flex PCB with perfect cutting performance.   With fast speed, high precision of ±0.02mm and high stability, RFH 355 series UV laser has become a well-known brand among FPC and PCB cutting, drilling, depanling and engraving clients.   
RFH UV laser is applicable to cut, drill an depanel on FPC
 cutting tempered glass
RFH 532nm green laser high-end marking car windshield LOGO
RFH 532nm green laser high-end marking car windshield LOGO   The customer uses the RFH green laser to hit the car windshield with high-definition, no blur   As an important part of car appearance, car windshield has strict requirements in production. The green laser marking logo on the windshield has also caused a lot of trouble in the industry. Some glass manufacturers once thought that the logo on the windshield should not be too tangled, so they used a weak marking technique. But it makes the quality unable to pass. Therefore, it can be seen that the text and pattern content such as the logo and model number marked on the windshield not only need to be fully presented on the glass, but also need not be corroded during the long-term baptism of wind and sand.
 cutting tempered glass
 KN95 mask marking
RFH UV laser is used for KN95 mask marking, less than one second
RFH UV laser is used for KN95 mask marking, less than one second 3W5W UV laser marking KN95 mask date and information 355mm UV cold light source, will not damage the mask   With the spread of the epidemic around the world, people's demand for masks continues to increase, and major mask manufacturers are also working hard to increase the production of masks. Among them, mask marking is an indispensable and important part of the production process. The printing mark of KN95 masks is generally printed on the outside of the mask. The content on it generally includes the mask model, related certificates, production date, etc., which is an important means of inspecting the quality and quality of the mask.
 KN95 mask marking
engraves LOGO word on ceramic surface
Ultraviolet solid-state laser engraves LOGO word on ceramic surface
Ultraviolet solid-state laser engraves LOGO word on ceramic surface, which is high-definition and delicate. Nanosecond solid-state laser engraves ceramic LOGO word pattern with 0.002mm high precision. Jiangsu customer has purchased S9 UV solid-state laser for LOGO word engraving on ceramic surface.   RFH UV solid-state lasers are used in ceramic marking and lettering, which can leave clear word and images on hard ceramics. Ultraviolet laser is a cold light source. The thermal influence is particularly small during laser cutting or marking. It has a narrow pulse width and higher peak power. It is easy to break through their damage to materials with higher breaking thresholds such as ceramics and sapphire. So it is suitable for processing high polymer materials that require high damage threshold.
engraves LOGO word on ceramic surface
Cutting quartz glass
Cutting quartz glass, both 15w high-power UV laser and green laser are capable
Cutting quartz glass, both 15w high-power UV laser and green laser are capable   Quartz glass has a very prominent position in the current market, especially in the decoration market which plays a very important role.
Cutting quartz glass
Get the latest offers Subscribe for our newsletter

Please read on, stay posted, subscribe, and we welcome you to tell us what you think.

leave a message
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

About

contact