10W-15W uv laser

UV laser source is used for cutting earphone film without scorching

UV laser source is used for cutting earphone film without scorching

 

In the production process of the earphone film, the most easily encountered problem is how to ensure the accuracy of its cutting and the problem of turning black and yellow after the earphone film is cut.

  • Laser Wavelength:

    354.7nm
  • Average Output Power :

    3W-10W @30kHz
  • Pulse Width:

    <14ns @ 30kHz
  • Pulse Repetition Rate :

    10-200kHz
  • Spatial Mode:

    TEM00
  • Beam Quality (㎡) :

    <1.2
  • Beam Diameter:

    0.8±0.2mm Measured at window
  • Beam Full Divergence Angle :

    <1.2mrad
  • Beam Circularity:

    >90%
  • Pulse-To-Pulse Stability:

    <2% RMS/@30kHz
  • Average Power Stability :

    <5% RMS/8hr
  • Beam-Pointing Drift:

    <30μrad/℃
  • Polarization Ratio:

    >100:1
  • Polarization Orientation:

    Horizontal
  • Operating Temp. & RH:

    10℃ to 30℃ | <80%
  • Storage Temp. & RH:

    -20℃ to 65℃ | <90 %
  • Electricity Requirement :

    100-240VAC |50/60Hz | Single phase
  • Power Consumption:

    <500W
  • Warranty :

    18months
  • Product Detail
  • Video

uv laser

UV laser source is used for cutting earphone film without scorching

 

In the production process of the earphone film, the most easily encountered problem is how to ensure the accuracy of its cutting and the problem of turning black and yellow after the earphone film is cut.

 

In order to cut more accurate earphone film, the headset manufacturer from Dongguan ordered two UV lasers from RFH to participate in the cutting of the earphone film. In the past, the earphone film cutting used the traditional cutting mode, and the traditional mode is no longer used in the current production in terms of speed, quality and cost. On the other hand, RFH UV laser, 335nm wavelength, small spot and frequent speed of light, make this non-contact processing method of laser more suitable for the production of earphone film.

 

In order to solve the problem of cutting accuracy, RFH chose a cold light source with narrow pulse width and high peak power to make its cutting accuracy up to 0.2mm, which fully meets the installation requirements of the earphone film. In addition, the output energy of cold-worked violet light can stimulate the photochemical reaction of the material, and avoid the blackening, yellowing and deformation of the material caused by excessive heat output at the same time .

uv laser | green laser | Ultraviolet lasers | uv dpss laser | nanosecond laser | UV laser source | Solid State Lasers

 

 

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Related products
UV laser
UV laser can cut screen protector tempered glass film with smooth and even cutting edges
RFH 355nm UV laser can cut screen protector tempered glass film with smooth and even cutting edges   With touch screen being increasingly used, the demand of mobile phone tempered glass film is also increasing. However, the sizes of different mobile phone brands are different, so the tempered glass film needs to be cut and drilled to required size. In the past, people used traditional CNC cutting technique on tempered glass film, but this method can easily lead to micro cracks or broken edges. So how to prevent tempered glass film from damaging during the cutting process? Well, RFH UV laser can help. The tempered glass film using RFH 355 series UV laser to drill and cut on won’t damage because of heat or crack because of instability. Instead, its cutting edges are quite smooth and the drilled holes are very round, making it more suitable to be used in smart phones.
UV laser
RFH UV laser for cutting and drilling screen protector tempered glass film for for iPhone
RFH UV laser for cutting and drilling screen protector tempered glass film for for iPhone
RFH UV laser for cutting and drilling screen protector tempered glass film for for iPhone With touch screen being increasingly used, the demand of mobile phone tempered glass film is also increasing. However, the sizes of different mobile phone brands are different, so the tempered glass film needs to be cut and drilled to required size. In the past, people used traditional CNC cutting technique on tempered glass film, but this method can easily lead to micro cracks or broken edges. So how to prevent tempered glass film from damaging during the cutting process? Well, RFH UV laser can help. The tempered glass film using RFH 355 series UV laser to drill and cut on won’t damage because of heat or crack because of instability. Instead, its cutting edges are quite smooth and the drilled holes are very round, making it more suitable to be used in smart phones.   
RFH UV laser for cutting and drilling screen protector tempered glass film for for iPhone
 3W5W UV laser
3W5W UV laser creates endurable marking on plastic tube
RFH 3W5W UV laser creates endurable marking on plastic tube To make the patterns and words on the plastic tube more durable, many tube manufacturers choose to use UV laser to mark on the plastic tube. Recently, Mr. Chen, who is a tube producer, ordered two units of UV laser marking machine and selected RFH 355 series UV laser as the laser generator.   RFH UV lasers feature with ultra-compact, high stability, high efficiency, high reliability and excellent laser beam quality.   The UV laser produced by RFH can solve the problem of marking on glossy tube. Using this UV laser can mark durable patterns and words on the surface of the plastic tube thoroughly against oxidation. This greatly help extend the service lifetime of the plastic tube.   
 3W5W UV laser
355nm UV laser
355nm UV laser is used to do antioxidant marking on plastic tube
355nm UV laser is used to do antioxidant marking on plastic tube To make the patterns and words on the plastic tube more durable, many tube manufacturers choose to use UV laser to mark on the plastic tube. Recently, Mr. Chen, who is a tube producer, ordered two units of UV laser marking machine and selected RFH 355 series UV laser as the laser generator.   RFH UV lasers feature with ultra-compact, high stability, high efficiency, high reliability and excellent laser beam quality.   The  UV laser produced by RFH can solve the problem of marking on glossy tube. Using this UV laser can mark durable patterns and words on the surface of the plastic tube thoroughly against oxidation. This greatly help extend the service lifetime of the plastic tube.   
355nm UV laser
Using RFH UV laser to mark on plastic package with incredible speed
Using UV laser to mark on plastic package with incredible speed
Using RFH UV laser to mark on plastic package with incredible speed Production date is the key information on food plastic package and needs to be clear and recognizable for consumers. To prevent the retailers from reselling the expired food to the consumers by replacing the old production date with the new one, more and more food producers choose to use UV laser marking machine to mark production date on the food package.   Last week, a food producer from Shantou ordered 2 units of UV laser marking machines which are equipped with RFH UV laser. After using RFH UV laser to mark on food plastic package, the marking speed becomes incredibly fast, for it takes less than a second to finish the marking process. This makes RFH UV laser very ideal for flying laser marking and assembly ling marking with faster marking speed and high quality.   
Using RFH UV laser to mark on plastic package with incredible speed
RFH 355 UV laser can create clear and lasting marking on plastic package
RFH 355 UV laser can create clear and lasting marking on plastic package
RFH 355 UV laser can create clear and lasting marking on plastic package Production date is the key information on food plastic package and needs to be clear and recognizable for consumers. To prevent the retailers from reselling the expired food to the consumers by replacing the old production date with the new one, more and more food producers choose to use UV laser marking machine to mark production date on the food package.   Last week, a food producer from Shantou ordered 2 units of UV laser marking machines which are equipped with RFH UV laser. After using RFH UV laser to mark on food plastic package, the marking speed becomes incredibly fast, for it takes less than a second to finish the marking process. This makes RFH UV laser very ideal for flying laser marking and assembly ling marking with faster marking speed and high quality.   
RFH 355 UV laser can create clear and lasting marking on plastic package
Why RFH UV laser is often used in laser marking plastic button switch?
Why RFH UV laser is often used in laser marking plastic button switch
Why RFH UV laser is often used in laser marking plastic button switch? More and more manufacturers choose UV laser marking machine to create pattern and characters on the plastic button switch. The focal spot of UV laser is pretty small with little heat transfer to surrounding material, so UV laser is also called “cold light source”. Because of this feature, heat effect won’t occur. Thus, distorting or burning of materials is no longer an issue.    Professional UV laser manufacturer - Shenzhen RFH Laser Technology Co.,Ltd    With 13 years of experience, the S9 series nanosecond UV laser developed and produced by RFH can engrave clear characters on the keyboard and the mouse. These kinds of characters can not only help people identify different buttons in the dark but also last long, for there are slightly protruding part on the buttons. This improves the durability and practicability of the keyboard and the mouse.   
Why RFH UV laser is often used in laser marking plastic button switch?
UV laser
UV laser featuring cold processing for marking plastic button on keyboard
 UV laser featuring cold processing for marking plastic button on keyboard More and more manufacturers choose UV laser marking machine to create pattern and characters on the plastic button switch. The focal spot of UV laser is pretty small with little heat transfer to surrounding material, so UV laser is also called “cold light source”. Because of this feature, heat effect won’t occur. Thus, distorting or burning of materials is no longer an issue.    Professional UV laser manufacturer - Shenzhen RFH Laser Technology Co.,Ltd    With 13 years of experience, the S9 series nanosecond UV laser developed and produced by RFH can engrave clear characters on the keyboard and the mouse. These kinds of characters can not only help people identify different buttons in the dark but also last long, for there are slightly protruding part on the buttons. This improves the durability and practicability of the keyboard and the mouse.   
UV laser
Get the latest offers Subscribe for our newsletter

Please read on, stay posted, subscribe, and we welcome you to tell us what you think.

Leave A Message
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

About

contact